Arc Flash PPE Categories 1 to 4: Chart and Label Meaning

Last Updated: 2026-10-26

Answer Capsule: Arc flash PPE categories come from NFPA 70E-2024 Table 130.7(C)(15)(c). CAT 1 requires a minimum arc rating of 4 cal/cm2, CAT 2 requires 8 cal/cm2, CAT 3 requires 25 cal/cm2 and CAT 4 requires 40 cal/cm2. A label shows either a PPE category or an incident energy value, never both, because NFPA 70E 130.5(G) allows one method per equipment.

A new hire walks up to a panelboard, reads "CAT 2" on the label, and asks what to put on. The lead hands over an 8 cal shirt and pants and says "that one." Next week the same hire opens a motor control center that says "8.7 cal/cm2 at 18 in" and asks the same question.

Both labels are telling the crew what to wear, in two different languages. One uses an arc flash PPE category and the other uses incident energy. Mixing them up is how a crew ends up under-dressed for a task, or in a 40 cal suit for a job that needed a face shield.

This guide from Print Pro AZ lays out the four arc flash PPE categories in a chart, explains what a category on a label means, and shows why a compliant label never shows both. Brent Hanke, founder of Print Pro AZ, catches the "both on one label" error in incoming study files more than any other.

What Are the Arc Flash PPE Categories?

Arc flash PPE categories are four levels of arc-rated clothing and gear defined in NFPA 70E-2024 Table 130.7(C)(15)(c), each with a minimum arc rating in cal/cm2. Here is the chart.

Category Minimum arc rating Typical arc-rated clothing (confirm against Table 130.7(C)(15)(c))
CAT 1 4 cal/cm2 Arc-rated shirt and pants or coverall, arc-rated face shield, hard hat, safety glasses, hearing protection, leather or arc-rated gloves
CAT 2 8 cal/cm2 Same items at an 8 cal/cm2 rating, with an arc-rated face shield and balaclava or an arc flash suit hood
CAT 3 25 cal/cm2 Arc flash suit jacket and pants or coverall with suit hood, rated 25 cal/cm2 or higher, plus arc-rated gloves
CAT 4 40 cal/cm2 Arc flash suit jacket and pants or coverall with suit hood, rated 40 cal/cm2 or higher, plus arc-rated gloves

The minimum arc rating is the number that matters. Every arc-rated layer or system you wear for that category must carry an arc rating at or above the category minimum.

Below 1.2 cal/cm2, no category applies. NFPA 70E does not require arc-rated PPE for arc flash when incident energy at the working distance is below 1.2 cal/cm2. Shock PPE still applies.

The clothing column above is a summary. Use NFPA 70E-2024 Table 130.7(C)(15)(c) for the full list of required items for each category.

What Does "CAT 2" on an Arc Flash Label Mean?

"CAT 2" on an arc flash label means the equipment was assessed using the PPE category method, and a worker inside the arc flash boundary must wear arc-rated PPE with a minimum arc rating of 8 cal/cm2. It tells you the outcome of a table lookup, not the exact incident energy.

NFPA 70E-2024 Section 130.5(G) lets the employer choose the PPE category method. The engineer matches the equipment type, voltage, fault current and clearing time to Table 130.7(C)(15)(a) for AC or Table 130.7(C)(15)(b) for DC. The table returns a category and an arc flash boundary.

What a CAT 2 label tells your crew:

  • Wear arc-rated PPE rated at least 8 cal/cm2 inside the arc flash boundary
  • The arc flash boundary printed on the label came from the same table
  • The equipment fell within the table's fault current and clearing time limits

If someone needs the actual cal/cm2, the equipment needs an incident energy analysis instead.

Preview of the Arc Flash Label Field Guide PDF
Free download · 2-page field guide

Print the Arc Flash Label Field Guide

A 2-page field card: the four items NEC 2026 now requires on every label, the PPE category table, the table-method disqualifiers, and the changes that force a relabel. Print it and keep it in the truck.

The download link appears instantly. No spam, and you can unsubscribe anytime.

Arc flash label printed by Print Pro AZ
Arc flash labels · printed in Phoenix

Need arc flash labels for a job? Get a quote in one business day.

Send us your study data or PPE categories. We print NEC 2026 compliant arc flash labels on UV-rated polyester and ship the same week.

Optional. PDF, Excel, CSV, DWG or images, up to 20 MB. Arc flash study reports and equipment lists are perfect.

No commitment. A real person replies within one business day.

Category vs Incident Energy: Which One Goes on the Label?

Either one can go on the label, but not both, because NFPA 70E-2024 Section 130.5(G) requires you to pick one method for each piece of equipment.

Item PPE category method Incident energy analysis method
NFPA 70E section 130.5(G) with Table 130.7(C)(15)(a) or (b) 130.5(G) with a calculation per IEEE 1584-2018
What the label shows "Arc Flash PPE Category 2" or similar "8.7 cal/cm2 at 18 in" or similar
Where the number comes from Table lookup by equipment type and parameters Engineering calculation from your system data
How the crew picks PPE Match the category to Table 130.7(C)(15)(c) Arc rating at or above the incident energy
When it cannot be used Equipment outside the table limits or not listed Any equipment, given a study
Precision Coarse: four buckets Specific: one value per equipment

The incident energy method gives you a specific number. On the Print Pro AZ sample label, MSB-1 reads 8.7 cal/cm2 at 18 inches, so the crew picks arc-rated clothing rated 8.7 cal/cm2 or higher. Print Pro AZ explains where that number comes from in its guide to how incident energy in cal/cm2 is calculated.

The category method skips the calculation in exchange for a coarser answer, and it cannot be used for equipment outside the table.

Why Does an Arc Flash Label Never Show Both?

An arc flash label never shows both a PPE category and an incident energy value because NFPA 70E-2024 Section 130.5(G) permits only one method per piece of equipment, and mixing them creates conflicting instructions.

Here is the conflict. The incident energy method might return 8.7 cal/cm2. A worker who sees "CAT 2" on the same label reaches for 8 cal gear, rated below the calculated exposure. The label just told the worker two different things.

Print Pro AZ rule: if a study table has both a "PPE Category" column and an "Incident Energy" column filled in for the same equipment ID, one of them has to go before the label prints. Brent Hanke sends those files back with the column circled. Both-on-one-label is one of the five inspection failures in the Print Pro AZ field guide.

A label that shows both values invites the question of which one the employer meant. For the full label content rules under 130.5(H), see the Print Pro AZ guide to arc flash labels under NFPA 70E 2024.

When Can You Not Use the PPE Category Method?

You cannot use the PPE category method when the equipment falls outside the limits of Table 130.7(C)(15)(a) or (b), and in that case NFPA 70E-2024 requires an incident energy analysis instead. The four disqualifiers:

  1. Available fault current above the table limit for that equipment type.
  2. Protective device clearing time above the table limit for that equipment type.
  3. Equipment type not listed in the table at all.
  4. Equipment not properly installed and maintained.

Here is a call Print Pro AZ gets every month. A contractor sends a label list for a plant expansion with "CAT 2" on every row, including a 4000 A switchgear lineup. The category came from a rule of thumb, not from the table.

Print Pro AZ asks for the study. The switchgear ends up with an incident energy label after the engineer runs the calculation.

What Is a 40 Cal Suit and When Do You Need It?

A 40 cal suit is an arc flash suit with an arc rating of at least 40 cal/cm2, and it is the minimum PPE for CAT 4 under NFPA 70E-2024 Table 130.7(C)(15)(c).

You need a 40 cal suit when:

  • The label reads "Arc Flash PPE Category 4"
  • The label reads an incident energy above 25 cal/cm2 and up to 40 cal/cm2 at the working distance

You do not automatically need a 40 cal suit for every task on high-energy gear. Equipment placed in an electrically safe work condition under NFPA 70E-2024 Section 120.5 removes the arc flash exposure for the task.

What about incident energy above 40 cal/cm2? The table stops at CAT 4. Above 40 cal/cm2, the incident energy method still applies and the arc rating of the PPE must still meet or exceed the number. Many owners switch the signal word to DANGER above 40 cal/cm2, but NFPA 70E does not set that cutoff. It is a program decision.

How Do You Pick Arc Rated Clothing From the Label?

You pick arc rated clothing by reading which method the label uses, then matching the arc rating to either the category minimum or the incident energy value. It takes three steps.

  1. Read the method. If the label shows "Arc Flash PPE Category," go to Table 130.7(C)(15)(c). If it shows a cal/cm2 value, use that number directly.
  2. Match the arc rating. For a category, wear the listed items rated at or above the category minimum. For an incident energy value, wear arc-rated clothing and head protection rated at or above the value.
  3. Add shock protection. The limited and restricted approach boundaries on the label come from NFPA 70E Table 130.4(E)(a) for AC and (b) for DC. Inside the restricted approach boundary, voltage-rated gloves and tools apply regardless of the arc flash method.

OSHA ties this together under 29 CFR 1910.132(d), which requires a written PPE hazard assessment. The arc flash label is the field output of that assessment.

Print Pro AZ prints the label that carries the category or the incident energy on UV-rated polyester or .048 aluminum. For outdoor gear, the aluminum arc flash and shock hazard label holds up where a vinyl sticker peels.

Preview of the Arc Flash Label Field Guide PDF
Free download · 2-page field guide

Take the field guide with you

Everything in this article on one printable card: required label fields, PPE categories, table-method rules, and relabel triggers. Free to share with your crew.

The download link appears instantly. No spam, and you can unsubscribe anytime.

Arc flash label printed by Print Pro AZ
Arc flash labels · printed in Phoenix

Ready to label the gear? Get a quote in one business day.

Tell us the equipment and the count. We handle the rest, from study data to a durable label that passes inspection.

Start my quote

Or browse arc flash labels and order online.

Frequently Asked Questions

What is CAT 2 arc flash PPE?

CAT 2 arc flash PPE is arc-rated clothing and gear with a minimum arc rating of 8 cal/cm2 under NFPA 70E-2024 Table 130.7(C)(15)(c). It typically includes an arc-rated shirt and pants or coverall plus a face shield with balaclava or a suit hood.

Is there a CAT 0 or a CAT 5 in NFPA 70E?

No. NFPA 70E-2024 Table 130.7(C)(15)(c) lists four categories, 1 through 4. Below 1.2 cal/cm2 no arc-rated PPE is required for arc flash. Above 40 cal/cm2 there is no category, and the incident energy method applies with PPE rated at or above the calculated value.

What does 8.7 cal/cm2 on a label mean for PPE?

It means the worker at the stated working distance needs arc-rated clothing and head protection with an arc rating of at least 8.7 cal/cm2. Because the label uses the incident energy method, it will not show a category.

Does the PPE category cover shock protection?

No. The arc flash PPE category covers thermal protection from an arc. Shock protection depends on the voltage and the limited and restricted approach boundaries from NFPA 70E Table 130.4(E). Voltage-rated gloves and insulated tools are required inside the restricted approach boundary regardless of the category.

Conclusion

Arc flash PPE categories 1 through 4 carry minimum arc ratings of 4, 8, 25 and 40 cal/cm2 under NFPA 70E-2024 Table 130.7(C)(15)(c). A label shows either a category from the table method or an incident energy value from a calculation, and NFPA 70E 130.5(G) never allows both on the same equipment.

Getting the method right on every label saves your crew from guessing at the panel and saves you an inspection re-trip. Print Pro AZ prints category labels and incident energy labels from your study data and checks for the both-on-one-label error before anything prints.

Have a facility or commercial job? Send us your plan sets and Print Pro AZ will build the label set. Questions? Call Brent: (602) 649-5305.

Sources

Brent Hanke | Print Pro AZ | (602) 649-5305 | b.hanke@printproaz.com

Brent Hanke is the founder of Print Pro AZ, supplying NEC-compliant labels to contractors across the country.


Tags:
NFPA 704 Labels: Acceptable Workplace Labels Under HazCom?

HMIS vs NFPA 704 Labels: Differences and When to Use Each