Last Updated: 2026-10-29
Answer Capsule: NFPA 70E training is required for every employee exposed to electrical hazards, but there is no NFPA 70E certification. NFPA does not certify individuals. Under NFPA 70E-2024 Section 110.6, the employer trains workers as qualified or unqualified persons, documents it, and retrains at intervals not to exceed 3 years or sooner when duties, equipment or procedures change.
The GC's safety officer wants a copy of your crew's "NFPA 70E certification" before anyone touches the switchgear. You search for it and find a dozen vendors selling wallet cards. None of them are from NFPA, because NFPA does not certify people. What the safety officer actually needs is proof that your crew received NFPA 70E training that meets Section 110.6, and that it is still current.
This guide explains what NFPA 70E training is, who counts as a qualified person, how often retraining is required, and what records you must keep. Print Pro AZ works with contractors who get asked this question on every commercial bid, and Brent Hanke has watched crews lose a day on site because the paperwork was missing.
Is There an NFPA 70E Certification?
No. NFPA publishes the standard, but it does not certify or license individual workers on NFPA 70E. Any "certification" you see comes from a training provider, and it is really a certificate of completion. That is fine as a record, but it carries no legal weight by itself.
What carries weight is Section 110.6 of NFPA 70E-2024, which puts the training duty on the employer. The employer must train employees exposed to electrical hazards, decide who is qualified for which tasks, document the training, and retrain on schedule. A wallet card can be part of that record, not a replacement for it.
What to tell the safety officer: you will send the training records required by NFPA 70E 110.6, showing each employee's name, the content covered and the dates. That is the answer OSHA would look for too.
Who Needs NFPA 70E Training?
Every employee who could be exposed to an electrical hazard needs NFPA 70E training, and the standard splits them into two groups: qualified persons and unqualified persons. The training is different for each, but neither group is exempt.
- Qualified persons are the people who work on or near exposed energized parts: electricians, maintenance techs, controls techs, solar crews commissioning inverters. They need the full program.
- Unqualified persons are everyone else who could be exposed: laborers, painters, HVAC techs pulling a disconnect cover, supervisors walking the electrical room. They need awareness training so they recognize the hazard and stay outside the boundaries.
The rule follows the exposure, not the job title. A project manager who never opens a panel still needs to know what the limited approach boundary means if the panel is open when they walk by. The employer decides who lands in which group.
Print the Arc Flash Label Field Guide
A 2-page field card: the four items NEC 2026 now requires on every label, the PPE category table, the table-method disqualifiers, and the changes that force a relabel. Print it and keep it in the truck.
The download link appears instantly. No spam, and you can unsubscribe anytime.

Need arc flash labels for a job? Get a quote in one business day.
Send us your study data or PPE categories. We print NEC 2026 compliant arc flash labels on UV-rated polyester and ship the same week.
No commitment. A real person replies within one business day.
What Makes Someone a Qualified Person Under NFPA 70E?
A qualified person under NFPA 70E is someone who has demonstrated skills and knowledge related to the construction and operation of the electrical equipment, and has received safety training to identify the hazards and reduce the risk. Both halves matter. A journeyman card proves the first half. Only NFPA 70E training proves the second.
Qualified is also specific to the equipment and the task. A tech who is qualified on a 480 V motor control center is not automatically qualified on 15 kV switchgear or a battery energy storage system. The employer must be able to show that training covered the equipment the worker actually touches.
| Qualified person | Unqualified person | |
|---|---|---|
| Can work inside the limited approach boundary | Yes, with the right PPE | No |
| Can perform an arc flash risk assessment for a task | Yes | No |
| Can verify an electrically safe work condition | Yes | No |
| Training needed | Full 110.6 program, equipment-specific, with demonstrated skills | Awareness of hazards and boundaries |
| Retraining interval | Not to exceed 3 years, plus change triggers | Not to exceed 3 years, plus change triggers |
Callout: a qualified person must be able to read the arc flash label and act on it. If a worker cannot say whether the label shows incident energy or a PPE category, or where the arc flash boundary is, they are not ready to work energized. The Print Pro AZ guide to reading an arc flash label field by field is a good training handout.
How Often Is NFPA 70E Retraining Required?
NFPA 70E-2024 Section 110.6 requires retraining at intervals not to exceed 3 years. That is the outside limit, not the target. The standard also expects additional training or retraining sooner when any of these happen:
- Supervision or inspection shows an employee is not following the safety-related work practices.
- New technology, new equipment types or changes in procedures arrive on site.
- An employee needs to use practices not normally used during regular job duties.
A new edition of NFPA 70E is another good reason to retrain, because section numbers and requirements move. The 2024 edition renumbered the training section to 110.6, and the next edition is expected on the three-year cycle. Employees exposed to shock hazards also need emergency response training such as contact release and CPR, with refreshers on whatever schedule the certifying body sets.
How Brent Hanke recommends handling it: put every employee's training date in the same spreadsheet you use for label review dates. Both run on multi-year clocks, both get forgotten, and both get asked for on the same audit.
What Should NFPA 70E Training Cover?
NFPA 70E training for a qualified person must cover the hazards, the boundaries, the PPE and the procedures for the equipment that person works on. Section 110.6 allows classroom training, on-the-job training or both, but the employer must confirm the worker can actually perform the skills. Here is the core content:
- The electrical safety program required by Section 110.3, including job briefings and who to call.
- The three hazards: shock, arc flash and arc blast, and what each one does to a body.
- The boundaries: limited and restricted approach boundaries from Table 130.4(E)(a) and the calculated arc flash boundary.
- How to read the equipment label under 130.5(H), including why a label never shows both incident energy and a PPE category.
- PPE selection under 130.7, including the arc-rated categories and when no arc-rated clothing is required below 1.2 cal/cm2.
- Establishing an electrically safe work condition under 120.5, which is the lockout process, and how it lines up with OSHA 1910.147.
- Test instrument use and verifying absence of voltage.
- Emergency response: contact release, CPR and AED use.
Unqualified person training is shorter. It covers what the hazards are, what the labels and signs mean, and the rule to stay outside the boundaries unless escorted by a qualified person.
How Do You Document NFPA 70E Training?
Section 110.6 requires the employer to document that each employee received the training, and the record must include the content, the employee's name and the dates. Keep it for as long as the employee works for you. Keep a one-page record per employee inside the electrical safety program binder, plus the provider's certificate.
OSHA does not have a rule titled "NFPA 70E training," but its work practice rules in 29 CFR 1910.333 assume employees know how to work safely on or near energized parts. A 2006 OSHA letter of interpretation calls NFPA 70E a widely accepted approach, so a compliance officer who asks for training records will measure them against 110.6. No record means, in OSHA's eyes, no training.
Where Do Labels Fit Into NFPA 70E Training?
The arc flash label is the field test of the training, because it is where a worker has to turn what they learned into a PPE choice in about ten seconds. Training teaches the words. The label supplies the numbers.
Here is a call Print Pro AZ gets every month. A contractor's new hires all passed a 70E class, but on their first energized task none of them could say whether the label showed incident energy or a category, or where 4 ft 6 in was measured from. The foreman ordered a fresh label set and used the printed labels as the hands-on portion of the retraining. Brent Hanke's advice: train on the actual labels in your building, not a stock slide.
That only works if the labels are right. Print Pro AZ prints arc flash labels from your study data on UV-rated polyester and .048 aluminum, and the full content rules are in the NFPA 70E 2024 arc flash label requirements guide.
Take the field guide with you
Everything in this article on one printable card: required label fields, PPE categories, table-method rules, and relabel triggers. Free to share with your crew.
The download link appears instantly. No spam, and you can unsubscribe anytime.

Ready to label the gear? Get a quote in one business day.
Tell us the equipment and the count. We handle the rest, from study data to a durable label that passes inspection.
Start my quoteOr browse arc flash labels and order online.
Frequently Asked Questions
Does OSHA require NFPA 70E training?
Not by name. OSHA requires employers to protect workers from electrical hazards under 29 CFR 1910 Subpart S and the General Duty Clause, and its 2006 letter of interpretation describes NFPA 70E as a widely accepted approach. In practice, documented NFPA 70E training under Section 110.6 is how employers show OSHA they met that duty.
How long is NFPA 70E training good for?
Up to 3 years. NFPA 70E-2024 Section 110.6 sets retraining at intervals not to exceed 3 years. You must retrain sooner if supervision shows non-compliance, if new equipment or procedures arrive, or if an employee takes on tasks outside normal duties.
Can NFPA 70E training be done online?
NFPA 70E does not ban online training, and Section 110.6 allows classroom, on-the-job or a combination. For qualified persons the employer must still confirm the worker can demonstrate the skills, so most contractors pair online content with hands-on work on their own equipment.
Is a journeyman license the same as being NFPA 70E qualified?
No. A license shows skills and knowledge of the equipment, which is half of the NFPA 70E definition. The other half is safety training to identify hazards and reduce risk, documented by the employer. A licensed electrician with no 70E training and no record is not a qualified person on paper.
Conclusion
There is no NFPA 70E certification, only documented training that meets NFPA 70E-2024 Section 110.6. Every exposed employee needs it, qualified persons need the equipment-specific version with demonstrated skills, and retraining runs on a clock that never exceeds 3 years. Keep the records with your electrical safety program, because that is what the safety officer and OSHA will ask to see.
Training your crew on correct labels saves you inspection delays and re-trips, and it makes the retraining stick. Have a commercial job coming up? Send us your plan sets and Print Pro AZ will produce the label set, or call Brent at (602) 649-5305.
Sources
- NFPA 70E, Standard for Electrical Safety in the Workplace: https://www.nfpa.org/codes-and-standards/nfpa-70e-standard-development/70e
- OSHA 29 CFR 1910.333, Selection and use of work practices: https://www.osha.gov/laws-regs/regulations/standardnumber/1910/1910.333
- OSHA standard interpretation, November 14, 2006, on NFPA 70E: https://www.osha.gov/laws-regs/standardinterpretations/2006-11-14
Brent Hanke | Print Pro AZ | (602) 649-5305 | b.hanke@printproaz.com
Brent Hanke is the founder of Print Pro AZ, supplying NEC-compliant labels to contractors across the country.