Last Updated: 2026-11-02
Answer Capsule: There is no fixed NFPA 704 rating for lithium-ion batteries. NFPA 704 rates chemicals from SDS data, and a battery is a sealed product, so the fire marshal sets the rating for the ESS room under IFC Chapter 12 and NFPA 855. Most require a custom placard with their numbers and chemistry text, paired with NEC Article 706 labels.
Here is a call Print Pro AZ gets more every month. A solar contractor is finishing a commercial battery install, the plan review comments say "provide NFPA 704 placard at ESS room," and the crew searches for the NFPA 704 rating for lithium-ion batteries. Every answer they find is different.
There is no single answer. A lithium-ion cell is a sealed product, not a chemical with a flash point, and NFPA 704 was written for drums of acetone and tanks of acid, not racks of cells.
This guide explains why there is no fixed rating, what fire marshals actually ask for, what IFC Chapter 12 and NFPA 855 require, and how to pair the placard with your NEC Article 706 labels. Brent Hanke at Print Pro AZ has printed custom ESS placards for enough jurisdictions to know the questions to ask before you order.
Why Is There No Fixed NFPA 704 Rating for Lithium-Ion Batteries?
There is no fixed rating because NFPA 704 rates a material from its safety data, and a lithium-ion battery is an assembled product, not a material with one SDS. The standard gives criteria, not ratings, and the facility owner or operator assigns the numbers.
Look at how the criteria work. Flammability is tied to flash point and boiling point, health to what a short exposure does to a person, and instability to detonation or violent reaction under heat or pressure. A sealed cell has no flash point. Its electrolyte does, but it sits inside a can inside a module inside a cabinet.
Manufacturers publish product safety data sheets for their cells, and some list an NFPA rating in Section 16. Those ratings vary from one maker to the next, and they rate the cell, not the room. That is why the rating for your ESS room comes from the fire marshal, the AHJ, and not from a table. The pillar guide to reading the NFPA 704 diamond explains what each number would mean once it is set.
What Do Fire Marshals Ask For at an ESS Room?
Fire marshals commonly ask for an NFPA 704 placard at the ESS room door or on the outdoor enclosure, with a rating they set during plan review, and often with special text added. Some also ask for a separate "Li-ion" or battery chemistry sign.
What that looks like in practice varies by city, and AHJs vary widely on this one. The typical requests Print Pro AZ sees on plan review comments:
- An NFPA 704 diamond with the AHJ's numbers in blue, red and yellow, and the white square either blank or with a symbol the AHJ specifies
- Text near the diamond naming the chemistry, such as "Lithium-Ion Battery Energy Storage System"
- A note on the total stored energy in kWh, sometimes on the same sign
- A "Do Not Use Water" or "Contact Fire Department Before Entry" instruction, when the AHJ wants it
Ask the fire marshal for the exact numbers and wording in writing before you order. A placard printed from a guess gets rejected at final. Print Pro AZ's lithium-ion battery room NFPA 704 placard lets you enter the AHJ's rating and text so the sign matches the approval.
Callout: Do not put "Li-ion" or "Battery" inside the white square of the diamond. NFPA 704 authorizes only three symbols there: W with a line through it, OX and SA. Chemistry text goes outside the diamond, on the same sign or a separate one.
Print the NFPA 704 Diamond Field Guide
A 2-page field card: how to read every quadrant, the three legal special symbols, sign size by viewing distance, and NFPA 704 ratings for 50 common chemicals with the matching part number. Print it and tape it inside the chemical room door.
The download link appears instantly. No spam, and you can unsubscribe anytime.

Need placards for a chemical room? Send your inventory, get a quote in one business day.
Attach your chemical inventory or SDS list. Print Pro AZ works out the room rating, prints the NFPA 704 placards on vinyl or aluminum, and ships the same week.
No commitment. A real person replies within one business day.
What Do IFC Chapter 12 and NFPA 855 Require?
IFC Chapter 12 governs energy systems, and Section 1207 in the 2021 edition covers stationary energy storage systems. NFPA 855 is the Standard for the Installation of Stationary Energy Storage Systems. Both point to hazard identification at the ESS location, and the placard rule itself comes through IFC Section 5003.5.
IFC 5003.5 requires hazard identification signs as specified in NFPA 704 on stationary containers and at entrances to locations where hazardous materials are stored, used or handled in quantities requiring a permit. A commercial lithium-ion ESS above the permit thresholds in Chapter 12 lands under that rule, and most fire marshals treat the room or enclosure as the "location."
NFPA 855 adds the installation side: separation distances, size limits per unit and per room, fire detection and suppression, ventilation, and signage that identifies the system and its hazards. The exact signage wording and placement come from the AHJ's adopted edition and their own amendments. Verify which edition of the IFC and NFPA 855 your city has adopted, because the ESS sections changed between cycles.
How Do You Get the Rating for Your ESS Placard?
You get the rating from the fire marshal, and the fastest path is to ask during plan review instead of at final inspection. Here is the sequence that works:
- Pull the cell or module product safety data sheet from the manufacturer. Note any NFPA rating in Section 16 and the hazard data in Sections 9, 10 and 11.
- Check the plan review comments for a stated rating or a sign schedule. Many AHJs write the numbers straight into the comments.
- If the comments are silent, ask. Send the fire marshal the SDS and the system data (chemistry, kWh, location) and request the NFPA 704 rating and any special text in writing.
- Confirm the size. NFPA 704 Table 9.1 sizes the diamond by viewing distance: 4 inch for 50 feet, 8 inch for 100 feet, 15 inch for 300 feet.
- Order the custom placard with the AHJ's numbers and text, on .040 aluminum for outdoor enclosures or vinyl for an interior door.
Keep the fire marshal's written rating in the closeout package. If the inspector at final differs from the plan reviewer, the letter settles it.
How Do NFPA 704 Placards Pair With NEC Article 706 Labels?
The NFPA 704 placard and the NEC Article 706 labels cover two different inspectors, and a commercial ESS needs both. The fire marshal reads the diamond; the electrical inspector reads the 706 labels.
National Electrical Code Article 706 covers energy storage systems on the electrical side. Its labels mark the ESS disconnecting means and identify the nominal voltage, battery chemistry and stored capacity at the equipment. The NFPA 704 diamond goes at the room entrance or on the outside of the enclosure for the responder.
The two sets work together. A firefighter arriving at night sees the diamond and the chemistry text at the door, then finds the disconnect by its 706 label. The label requirements for battery chemistry, voltage and capacity are covered in NEC 2026 Article 706 ESS labels, and the full set for a solar-plus-storage job is in the solar battery storage labels guide.
Which Placard Should You Order for a Battery Room?
Order a custom-rating NFPA 704 placard with the fire marshal's numbers, sized for the viewing distance and made for the location. Do not order a stock diamond with a rating you found online.
For an interior battery room door, a 9 inch or 11 inch vinyl diamond at eye level or above the door, clear of the swing, is the common choice. For an outdoor enclosure, 15 inch or larger .040 aluminum, because Arizona sun fades vinyl in a season. Add the chemistry text as a separate line or a companion sign, never inside the white square.
Here is a typical job. A solar contractor finishing a rooftop PV and ESS install in the Phoenix metro gets a plan review comment for an NFPA 704 placard at the enclosure. The crew calls Print Pro AZ with the fire marshal's rating and the chemistry text, and the custom placard ships with the NEC 706 label set so both inspectors are covered in one order. Partner companies that get the AHJ's rating in writing first report 45%+ better first-time inspection pass rates.
The free NFPA 704 Diamond Field Guide has ratings for 50 common chemicals; use the download form on this page to get it.
Take the field guide with you
Everything in this article on one printable card: the rating scales, the white square symbols, placement rules, and 50 chemical ratings. Free to share with your crew.
The download link appears instantly. No spam, and you can unsubscribe anytime.

Ready to placard the building? Get a quote in one business day.
Tell us the rooms, tanks and chemicals. We handle the rest, from the composite rating to an aluminum placard the fire marshal can read from the street.
Start my quoteOr browse NFPA 704 diamond signs and order online.
Frequently Asked Questions
What is the NFPA 704 rating for lithium-ion batteries?
There is no fixed rating. NFPA 704 gives criteria, not ratings, and a sealed battery has no single SDS to rate. The fire marshal sets the numbers for the ESS room or enclosure during plan review, and you print the placard to match.
Does NFPA 855 require an NFPA 704 sign?
NFPA 855 requires signage that identifies the energy storage system and its hazards, and the fire code, through IFC 5003.5, requires NFPA 704 hazard identification at locations with hazardous materials in permit quantities. Together they are why fire marshals ask for the diamond at the ESS room.
Do residential battery systems need an NFPA 704 placard?
Usually not, but ask your AHJ. Residential systems generally fall under NEC Article 706 labeling and the residential ESS provisions in the fire code. Commercial systems above permit quantities are where the NFPA 704 placard is standard.
Can I put "Li-ion" in the white square of the diamond?
No. NFPA 704 authorizes only W with a line through it, OX and SA in the white square. Put the chemistry text outside the diamond, on the same sign or on a separate battery chemistry sign.
Conclusion
There is no fixed NFPA 704 rating for lithium-ion batteries because the standard rates materials from SDS data and a battery is a sealed product. The fire marshal sets the rating for your ESS room under IFC Chapter 12 and NFPA 855, often with chemistry text. Pair the diamond at the door with NEC Article 706 labels at the equipment so both inspectors sign off.
Getting the rating in writing before you print saves you a rejected placard and a re-trip at final. Order the custom-rating lithium-ion battery room placard with your AHJ's numbers, or call Brent at (602) 649-5305 with the plan review comments.
Sources
- NFPA 855, Standard for the Installation of Stationary Energy Storage Systems
- 2021 International Fire Code
- NFPA 704, Standard System for the Identification of the Hazards of Materials for Emergency Response
Brent Hanke | Print Pro AZ | (602) 649-5305 | b.hanke@printproaz.com
Brent Hanke is the founder of Print Pro AZ, supplying NEC-compliant labels to contractors across the country.